Innokin iTaste MVP 20W Video Review & Giveaway!
Hi Folks– Join in the Review and Giveaway of the all new Innokin MVP 20 Watt Mod. As the name suggest, it is a variable voltage and wattage device capable of up to 20 watts and 7.5 volts. Also, Check out my teaser on the all new Aspire Atlantis sub ohm (.6) Tank.
Innokin iTaste MVP 20W
The new Innokin iTaste MVP 20W: 20 watts of intelligent vaping power in the legendary 100% stainless steel body of Innokin iTaste MVP. The MVP20W is now has been powered up to 20 watts and upgraded with a better chip and sleeker look. The iTaste MVP20W now has a high quality flush 510 spring loaded connection that is designed to connect perfectly with all standard 510 tanks. An EGO thread adapter is packaged with the MVP20W so you can also use eGo threaded tanks as well.
The Innokin iTaste MVP 20W is a variable voltage with a range of 3.3v-7.5v adjustable in 0.1 volt increments and variabel attage from 6.0w – 20.0w adjustable in 0.5 increments.The easy to use integrated ohm meter will display the resistance of any attached tank and the handy puff counter helps you keep track of your daily vaping habits.
The Innokin iTaste MVP 20W is smarter with a 32-bit ARM microprocessor which means far faster data processing power and superior vaping performance. The steady VDC power output with an output voltage accuracy of +-1% greatly reduces noise and increases battery life and reliability.
The large capacity of a internal 2600mah battery means you can depend on the long lasting power of the MVP20W and it’s also a backup portable charger that can power your mobile phone and other electronic devices.
Features and Specs:
Dimensions: 4.21″L x 1.61″W x 0.86″D
Voltage can be adjusted from 3.3 7.5 volts in .1 volt increments.
Wattage can be adjusted from 6.0 20.0 Watts in .5 watts increments.
Battery Level Indicator:
The MVP20W battery capacity is displayed via green, yellow and red LED.
Green = Almost fully Charged. When the MVP20W fully recharged the LED light will power off.
Yellow = Half Power.
Red = Low Power. Charge the MVP20W.
Large battery capacity:
The MVP20W has a built-in 2600 mAh polymer Li-Ion rechargeable battery.
ON/OFF battery switch:
Press the power button three times in rapid succession to turn on the MVP20W. When the MVP20W is powered on hold down the button to activate the atomizer and vape. When the MVP20W is not in use, press the button three times in succession to power off the MVP20W. Always power off the MVP20W when it is not being used, or when it is going to be stored in a pocket, bag or purse.
Reads the resistance of your atomizer/cartomizer/clearomizer.
The integrated Puff counter will record the number of puffs you have taken. Either press “P” button or “U” button for 1 second to check the number of puffs. The Puff Counter will reset to 0 whenever the device is powered off.
10 second Cutoff:
If the activation button is held for longer than 10 seconds the MVP20W will stop firing until the button is released and pressed again.
Low Voltage Warning:
The Red LED and Battery bar will continue blinking when the battery capacity is lower than 3.3V and the MVP20W will power off automatically.
Short Circuit/Atomizer Protection:
Short Circuit/Atomizer Protection protects the MVP20W against shorted atomizers and will stop the unit from functioning in unsafe conditions.
The MVP20W monitors the battery voltage and will automatically power off when the battery is discharged.
The MVP20W is recharged with a Micro USB cable. When plugged into a power source the MVP20W can also be vaped and charged at the same time with Innokin Technology’s Vape while you charge pass-through technology.
Remembers last Voltage or Wattage setting:
When the MVP20W is turned off it will store the current voltage or wattage setting and it will retain the setting when the MVP20W is powered on.
Built-in 3 digit display:
Digital display shows the Ohms meter, Voltage / Wattage setting and the number of Puffs taken since last time the battery was turned off.
Portable power source for electronic products
To charge your portable electronic device with the MVP20W – set the small pin switch on the bottom of the MVP20W to the ON position and connect a micro USB cable to the USB OUTPUT port (DC 5V, maximum output current 0.5A)To maximize the battery charge of your MVP20W please ensure that the bottom switch is set to the Off position when you are not using the portable charger function.
- Operating Voltage: 3.3V-7.5 V
- Operating Wattage: 6.0W-.20W
- Standby current: 100uA max
- Maximum output Wattage: 20W
- Maximum output Current：6A
- Maximum output Voltage: 7.5V
- Clearomizer Resistance: 1.0 Ohm (minimum)
- Battery: Built-in 2600 mAh polymer Li-Ion rechargeable battery.
- Charging: Micro USB DC5V/1000mA
- OUTPUT port ：DC5V /1000mA
Should the US FDA and the lawmakers in the capital manage to severely restrict the sale of advanced vaporizers and e liquid we will take a major hit on our personal freedoms and freedom of choice. Do not let this happen. Follow Spinfuel’s Vapers News daily, both positive and negative electronic cigarette news to stay informed on what is happening on the local, state, and federal regulations. This is the first time in American History where a product that can save millions of lives is being attacked daily. It is said that money is the root of all evil, and we can add that money is the root of all bad government decisions. Make sure your next vote is given to the candidate who believes in the most freedom.
Smokenjoey & Spinfuel
All Smokenjoey videos are available in Spinfuel eMagazine. Discover Smokenjoey’s fervent dedication to an honest and open electronic cigarette industry by watching new, and past videos under the Smokenjoey Category. From the early days of cig-a-like electronic cigarettes to the advanced vaporizers of 2015, Smokenjoey delivers a truthful account in every aspect of the electronic cigarette industry.
Other Places You Can Find Smokenjoey
Subscribe to Smokenjoey on YouTube
Visit Smokenjoey’s Homepage
Smokenjoey’s Spinfuel Page